May 5, 2021Summer Sanitation Is Important as Ever
To contact John Palumbo go to: jpalumbo@ag.Arizona.edu
When known weedy fields are ready to plant and labor is expected to be short, it is tempting to use all the preplant herbicides that are available. In lettuce, there are three preplant herbicides available and it is not uncommon to use 2 and occasionally all 3 on the same crop. All three of these herbicides use the same mode of action to kill weeds. There are slight differences between them but they all either stop or disrupt cell division in the roots and or stems of the weeds. They are normally safe to lettuce unless the crop is stressed or the rate, timing or placement are poor. The rationale for using multiple preplant herbicides in lettuce is often to broaden the weed control spectrum or guard against misses caused by misapplication or environmental conditions. There are some hazards, however, that sometimes outweigh the benefits. Potential crop injury is increased. All 3 use the same mode of action and the chance of injuring developing crop roots is compounded. Sometimes herbicides are added that contribute nothing but potential injury to the mix. If you look at the following chart you can see that many weeds are controlled by Kerb, for instance, that are not controlled by Balan or Prefar. Why add them? All three control grasses, goosefoot and purslane. If environmental conditions and applications are optimal it is often possible to use only one. Herbicides are much less expensive than labor, but it is possible to overdo it and cause more problems and expense.
It is about that time of the year/growing season when you start seeing bacterial diseases. With the rain we got last week and as plants get more vegetative growth bacterial issues become more prevalent. Cilantro and parsley are two crops grown in desert southwest that often suffer from bacterial leaf spots. Most times, the disease incidence is also high because of sprinkler irrigation used in these cropS. On both crops, initial symptoms of bacterial leaf spot are water-soaked lesions on leaves. The lesions develop into spots that are varying shades of tan or brown (see picture ‘B’ on parsley whereas advanced spots on cilantro can be black (see picture ‘A’ on cilantro). The lesions are usually limited by leaf veins and thus have an angular, square, or rectangular appearance, a typical feature of bacterial infection. Lesions tend to be relatively small about 1/8 to 1/4 inch (3–6 mm) in diameter and are visible from both the top and bottom of leaves. Under favorable conditions, free moisture from rain or sprinkler irrigation, leaf spots may coalesce and cause considerable blighting of the entire foliage.
Pseudomonas syringae pv. apii (Psa) and P. syringae pv. coriandricola (Psc). cause bacterial leaf spot on parsley and cilantro. Pseudomonas syringae pv. apii (Psa) can cause leaf blight in celery and fennel as well. Though the problem is documented as more of a problem in cilantro and less in celery, in severe condition the disease can result in unmarketable produce in any host. The bacteria are likely seedborne in both crops. However, water from rain, sprinkler irrigation, and heavy dews and fogs will splash bacteria from infected plants onto adjacent healthy foliage resulting in heavy infestation.
To manage the disease, always use tested/treated seeds, rotate crop with non-host to reduce inoculum level, switch from sprinkler to furrow irrigation to limit secondary spread, avoid excessive use of nitrogen fertilizer. Copper spray/copper based fungicide provide limited control against the pathogens.
Mark C. Siemens
Vol. 12, Issue 9, Published 5/5/2021
Automated thinning machines have been commercially available since 2012. These machines identify crop plants and intermittently deliver an herbicidal spray or dose of liquid fertilizer to thin the stand to the desired plant spacing. Some growers have converted older machines to spot apply pesticides to crop plants rather than thin lettuce. Spot spraying just the crop plant makes sense – it reduces applied chemical amount by about 1/3rd as compared to band spraying and by roughly 90% as compared to broadcast. I have heard reports of improved efficacy with this technique, perhaps due to better coverage, however this potential benefit has not been validated in formal trials.
A drawback with automated thinning machines is their high cost. Retail prices for machines are approximately $25,000 per seed line, or about $200,000 for a 4-row, 2-line machine. Another option might be to use automated systems designed for spot spraying weeds. These devices have been commercially available since the mid 90’s and function similarly to automated thinning machines in that they use optical sensors to detect plants and solenoid activated spray assemblies to intermittingly spray unwanted plants (Fig. 1). The cost of these devices is quite reasonable – about $3,000 per unit, or about $24,000 for a 4-row, 2-line machine.
Automated spot sprayers are typically used in agriculture to control weeds in fallow fields (Fig. 2), but could easily be adapted to apply pesticides or even fertilizer to vegetable crops. Spot applying foliar fertilizers to vegetable crops is an interesting concept and is being investigated in California with lettuce.
Another potential use of spot sprayers is to control herbicide resistant weeds. The device can be positioned between crop rows to spot spray a non-selective herbicide to target weeds. Placing the sprayer in a hooded enclosure prevents unwanted drift onto crop plants. We are conducting trials using this technique in cotton this season (Fig. 3). We are also looking for collaborators interested in trying the device as a pesticide and/or fertilizer spot applicator in vegetable crops for this upcoming season. If you are interested collaborating or would like to see a demo of the device, please feel free to reach out to me.
Growers and PCAs can monitor data from the Yuma Leaf Wetness Network through the AZMET website located at the following URL: http://22.214.171.124:460
The website updates information on leaf wetness and near-surface air temperature every 15 minutes. Wetness data are provided in graphical format (see figure below). Output from the leaf wetness sensors increase from the grey (dry) zone of the graph to the blue (wet) zone when wetness (dew or rain) is detected by the sensors.