May 5, 2021Summer Sanitation Is Important as Ever
To contact John Palumbo go to: jpalumbo@ag.Arizona.edu
When known weedy fields are ready to plant and labor is expected to be short, it is tempting to use all the preplant herbicides that are available. In lettuce, there are three preplant herbicides available and it is not uncommon to use 2 and occasionally all 3 on the same crop. All three of these herbicides use the same mode of action to kill weeds. There are slight differences between them but they all either stop or disrupt cell division in the roots and or stems of the weeds. They are normally safe to lettuce unless the crop is stressed or the rate, timing or placement are poor. The rationale for using multiple preplant herbicides in lettuce is often to broaden the weed control spectrum or guard against misses caused by misapplication or environmental conditions. There are some hazards, however, that sometimes outweigh the benefits. Potential crop injury is increased. All 3 use the same mode of action and the chance of injuring developing crop roots is compounded. Sometimes herbicides are added that contribute nothing but potential injury to the mix. If you look at the following chart you can see that many weeds are controlled by Kerb, for instance, that are not controlled by Balan or Prefar. Why add them? All three control grasses, goosefoot and purslane. If environmental conditions and applications are optimal it is often possible to use only one. Herbicides are much less expensive than labor, but it is possible to overdo it and cause more problems and expense.
With the start of melon season, you will also start seeing seedling diseases on melon. Bacterial fruit blotch (BFB) of melon is a common disease in melon seedlings that can stay in the crop until fruits/seeds are formed. You will be seeing more of this disease in greenhouse transplants.
Bacterial fruit blotch (BFB) of watermelon is caused by the bacterium Acidovorax avenae subsp. Citrulli. The bacteria produceslarge olive green to brown water-soaked lesions on fruit, making them unmarketable.
Symptoms of BFB on seedlings begin with water-soaked areas on the lower surface of the cotyledons and inconspicuous lesions on leaves. BFB lesions will become necrotic often with yellow halos. Lesions are frequently delimited by veins. Infected seedlings collapse and die.
Greenhouse conditions are usually favorable for dispersal and establishment of pathogen. Thus, good greenhouse practices and sanitation is extremely important. Clean transplant trays must be used (disinfect trays if they will be reused) and new soil. Destroy any volunteer seedlings and keep the area in and around the greenhouse weed free. Avoid overhead watering if at all possible, or water in the middle of the day so that the plants dry thoroughly before evening. The bacterium can spread on mist and aerosols. Relative humidity should be kept low through proper watering and good air circulation in the greenhouse. Separate different seedlots, to reduce lot-to-lot spread. Monitor these isolated seedlings daily and destroy trays where symptoms develop. The remaining trays should be sprayed with a labeled bactericide and the applications continued until the plants are transplanted to the field.
The pathogen can be seedborne, so growers should only use seed that has been tested for the presence of the pathogen by a reputable testing facility. Management of BFB includes a combination of preventing the introduction of the pathogen, sanitation to eliminate any inoculum present, and the use of bactericides if the disease appears. There are no commercially available watermelon cultivars that are resistant to bacterial fruit blotch, but there is some variation in susceptibility among cultivars.
Weed escapes are easy to spot in vegetable fields at harvest time. Some growers have these weeds pulled, bagged and removed by hand from the field because they are unsightly and to reduce seedbank loads. This can be a costly operation. An alternative solution might be to use high voltage electricity to kill these weeds. The idea of using electricity to “zap” weeds is not new. Machines for agriculture applications were developed decades ago and commercially available in the late 1970’s. Although the devices worked, they were not widely adopted due in part to the availability of low cost and efficacious herbicides.
Because of environmental concerns, herbicide resistant weed issues and increased organic production, non-chemical, high voltage weed control technology is seeing a resurgence. There are now five companies, three established within the last four years, offering or developing machines for commercial agriculture. Although configurations differ, all machines operate using the same principles. To explain, consider the example of the machine shown in Fig. 1. The unit comprises high voltage electrodes (8-15 kV) positioned above the crop canopy, an electric generator and a soil engaging coulter connected to ground. During operation, when an electrode touches a weed protruding above the canopy, current flows through the plant back to the generator via the ground contacting coulter. Current flow combined with electrical resistance in the plant causes rapid heating and plant fluids to vaporize. This ruptures cell walls and kills the plant. Although there are few recent reports in the literature, prior research on dated machines showed that the technique can provide better than 98% weed control in moderate weed densities (15,000 weeds/acre) at travel speeds of 2 mph (Diprose & Benson, 1984).
Modern approaches that utilize high voltage electricity in combination with smart machines to spot treat weeds are being developed. The idea is to use camera imagery and artificial intelligence to locate weeds and high voltage electricity to kill them. One such machine being developed by the MASCOR Institute1 and the Zasso Group is an autonomous robot equipped with cameras, on-board computers and robotic arms (Fig. 2). As the machine moves through the field, high voltage electrodes mounted on the movable, computer controlled robotic arms zap weeds. Another unit is being developed by Stekettee and RootWave. It is tractor pulled and designed to travel at 3 mph. Stekettee’s machine vision system identifies the weeds and RootWave’s high voltage electric technology shocks the weed with a pulsed 5 kV charge. Power is supplied by a generator connected to the tractor’s PTO. Both systems are in late stages of development with field tests conducted in 2020.
These systems appear promising and if they prove to be effective and economical, may be something to look for in the future.
1Reference to a product or company is for specific information only and does not endorse or recommend that product or company to the exclusion of others that may be suitable.
The Yuma County Leaf Wetness Network remains in place for the 2018/19 vegetable season. Growers and PCAs may access information generated by the network by entering the following internet address: http://184.108.40.206:460
Upon entering the address above, you will be transferred to internet page that provides a series of tabs at the top of the page. Simply click on the tabs to access the information of interest.