May 5, 2021Summer Sanitation Is Important as Ever
To contact John Palumbo go to: jpalumbo@ag.Arizona.edu
Oxyfluorfen,(Goal and Galigan) has become a popular and effective herbicide for use on cole crops even though it was first registered in the 1980’s. Oxyfluorfen is a contact herbicide with the same mode of action as Chateau, Aim, Shark, Gramoxone, Paraquat , Sharpen and ET. They are all PPO Inhibitors that rupture cell membranes. Carfentrazone (Aim, Shark), ET and Paraquat (Gramoxone), are effective only as postemergence applications to small weeds, Sharpen and Goal are effective both preemergence and early postemergence and Chateau is used only preemergence but can cause severe crop injury if mixed with a surfactant. The only one of these that is registered for cole crops is Oxyfluorfen (Goal, GoalTender, Galigan). It does not make sense for a contact herbicide to be used on weeds that have not emerged. The way this works is that a barrier is created with the herbicide on the surface that kills the seedling weeds as they come in contact with it. It is important not to disturb this barrier or the weeds will not be affected. Oxyfluorfen (Goal) is an herbicide that defies reason in other ways as well. It normally adheres strongly to the soil and has very low water solubility. It is well known, however, that Goal can lift off of the surface and cause crop injury. When this happens, it is evaporating or going from a liquid to a gas and this is unaffected by its solubility or adsorption. It also works well when chemigated through a sprinkler system. You would think that it would wash off, but it works well with less crop injury when chemigated. Chemigation is registered for onions only but it works well with cole crops as well. It only takes half as much (4 ounces) and is safer to the crop when chemigated. It is best to apply it about 2/3 of the way through the sprinkler run to keep it in place and flush the system.
Bindu Poudel, Martin Porchas Sr., and Rebecca Ramirez
Yuma Agricultural Center, University of Arizona, Yuma, AZ
This study was conducted at the Yuma Valley Agricultural Center. The soil was a silty clay loam (7-56-37 sand-silt-clay, pH 7.2, O.M. 0.7%). Melon variety: Deluxe (HMX2595)was seeded, then sprinkler-irrigated to germinate seed on March 31, 2020 on 84 inches between bed centers. All other water was supplied by furrow irrigation or rainfall. Treatments were replicated five times in a randomized complete block design. Each replicate plot consisted of 25 ft of bed. Treatment beds were separated by single nontreated beds. Treatments were applied with a tractor-mounted boom sprayer that delivered 50 gal/acre at 100 psi to flat-fan nozzles spaced 12 in apart.
Spray treatments were done on 5-21-2020, 5-28-2020, 6-4-2020, 6-11-2020.
Disease severity of powdery mildew (caused by Sphaerotheca fuliginea and S. fusca) severity was determined 6-19-2020 an d 6-19-22 by rating 10 plants within each of the four replicate plots per treatment using the following rating system: 0 = no powdery mildew present; 1 = one to two mildew colonies on leaves ;2 = powdery mildew present on one quarter of leaves; 3 = powdery mildew present on half of the leaves; 4 = powdery mildew present on more than half of leaf surface area ; 5 = powdery mildew present on entire leaf. These ratings were transformed to percentage of leaves infected values before being statistically analyzed.
The data in the table illustrate the degree of disease control obtained by application of the various treatments in this trial. Most treatments significantly reduced the final severity of powdery mildew compared to nontreated plants. The most effective fungicides included Luna Sensation, Torino SC, Quintec/Torino/Quintec/Torino in rotation, Mettle/Quintec/Torino/Quintec in rotation. Phytotoxicity symptoms were not noted for any treatments in this trial.
Mark C. Siemens
Vol. 12, Issue 9, Published 5/5/2021
Automated thinning machines have been commercially available since 2012. These machines identify crop plants and intermittently deliver an herbicidal spray or dose of liquid fertilizer to thin the stand to the desired plant spacing. Some growers have converted older machines to spot apply pesticides to crop plants rather than thin lettuce. Spot spraying just the crop plant makes sense – it reduces applied chemical amount by about 1/3rd as compared to band spraying and by roughly 90% as compared to broadcast. I have heard reports of improved efficacy with this technique, perhaps due to better coverage, however this potential benefit has not been validated in formal trials.
A drawback with automated thinning machines is their high cost. Retail prices for machines are approximately $25,000 per seed line, or about $200,000 for a 4-row, 2-line machine. Another option might be to use automated systems designed for spot spraying weeds. These devices have been commercially available since the mid 90’s and function similarly to automated thinning machines in that they use optical sensors to detect plants and solenoid activated spray assemblies to intermittingly spray unwanted plants (Fig. 1). The cost of these devices is quite reasonable – about $3,000 per unit, or about $24,000 for a 4-row, 2-line machine.
Automated spot sprayers are typically used in agriculture to control weeds in fallow fields (Fig. 2), but could easily be adapted to apply pesticides or even fertilizer to vegetable crops. Spot applying foliar fertilizers to vegetable crops is an interesting concept and is being investigated in California with lettuce.
Another potential use of spot sprayers is to control herbicide resistant weeds. The device can be positioned between crop rows to spot spray a non-selective herbicide to target weeds. Placing the sprayer in a hooded enclosure prevents unwanted drift onto crop plants. We are conducting trials using this technique in cotton this season (Fig. 3). We are also looking for collaborators interested in trying the device as a pesticide and/or fertilizer spot applicator in vegetable crops for this upcoming season. If you are interested collaborating or would like to see a demo of the device, please feel free to reach out to me.
Growers and PCAs can monitor data from the Yuma Leaf Wetness Network through the AZMET website located at the following URL: http://220.127.116.11:460
The website updates information on leaf wetness and near-surface air temperature every 15 minutes. Wetness data are provided in graphical format (see figure below). Output from the leaf wetness sensors increase from the grey (dry) zone of the graph to the blue (wet) zone when wetness (dew or rain) is detected by the sensors.
Beet armyworm: Moth counts remain very low consistent with seasonal temperatures, but below average for this point in the season.
Cabbage looper: Slight increase in activity, but moth counts remain unusually low for late January.
Whitefly: Dult movement is at seasonal low consistent with temperatures and lack of melons or cotton.
Thrips: Activity remains lower than normal for this point late January. Increased movement noted in Roll/Tacna.
Aphids: Seasonal aphid counts peaked during the past 2 weeks, suggesting movement with recent winter storms and lack of desert vegetation. Counts were particularly high in North Yuma and Gila Valleys, and Bard. Above average for this time of year.
Leafminers: Adult activity remains light in most trap locations. Trap counts increasing slightly in the South Gila Valley.